TECHNICAL
INFORMATION
<< Return to the Tech Info Page |
|
COOLING INFORMATION
Should I use an external
transmission cooler in conjunction with the oil cooler supplied
in the radiator?
Answer: Unless operating in an environment where the outside
temperature is below 0°F, you should cap off the radiator cooler
line openings and run your cooler lines directly to a new cooler
mounted in front of the radiator. This allows the transmission
to have its own cooling system and doesn't allow the engine
water temperature to heat the fluid.
What is the correct size cooler for my application?
Answer: Unlike a lot of items you buy for your vehicle,
bigger is predominately better when it comes to transmission
coolers. The answer would be as big as you can get or to run
multiple coolers in series, again staying away from the factory
radiator cooler lines.
Where should I mount a transmission cooler?
Answer: Monster Transmission highly recommends mounting your
external transmission oil cooler in front of the radiator. This
allows for adequate airflow. If this is not possible then you
should mount it in a location where the cooler can receive
airflow. In extremely tight quarters, you may also mount the
cooler and build an air dam that would allow the cooler to have
air pass through it.
GM Transmission Cooler Fittings
Powerglide - OEM
|
Fitting
Location |
Thread
Size |
Flow
Direction |
|
Upper |
1/8”
Pipe |
Return/in |
|
Lower |
1/8”
Pipe |
Cooler feed/out |
Powerglide -
Dedenbear
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Return/in |
|
Lower |
¼” Pipe |
Cooler feed/out |
TH200C Metric, 2004R
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Cooler feed/out |
|
Lower |
¼” Pipe |
Return/in |
TH350, TH250
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
1/8”
Pipe |
Return/in |
|
Lower |
1/8”
Pipe |
Cooler feed/out |
TH400
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Return/in |
|
Lower |
¼” Pipe |
Cooler feed/out |
700R4/4L60/4L60E/4L65E
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Return/in |
|
Lower |
¼” Pipe |
Cooler feed/out |
4L80E (1991-1996)
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Return/in |
|
Lower |
¼” Pipe |
Cooler feed/out |
4L80E/4L85E (1997 & later)
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Rear |
¼” Pipe |
Return/in |
|
Front |
¼” Pipe |
Cooler feed/out |
Ford Transmission Cooler Fittings
C3, C4, C5, C6
|
Fitting Location
|
Thread Size
|
Flow
Direction |
|
Front |
¼” Pipe |
Cooler feed/out |
|
Rear |
¼” Pipe |
Return/in |
AOD
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Cooler feed/out |
|
Lower |
¼” Pipe |
Return/in |
AODE/4R70W
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Upper |
¼” Pipe |
Return/in |
|
Lower |
¼” Pipe |
Cooler feed/out |
E4OD/4R100
|
Fitting
Location |
Thread Size
|
Flow
Direction |
| Front |
¼” Pipe |
Cooler feed/out |
|
Rear |
¼” Pipe |
Return/in |
Chrysler
Transmission Cooler Fittings
All Torqueflite
|
Fitting
Location |
Thread Size
|
Flow
Direction |
|
Front |
1/8”
Pipe |
Cooler feed/out |
|
Rear |
1/8”
Pipe |
Return/in |
|
Feel free to call or E-mail with any questions. Tech Dept.
(800) 708-0087 opt. 2# or E-mail
Click Here
|